MPL15100
DIODE PUMPED SUB-NANOSECOND ACTIVELY Q-SWITCHED LASER
MPL15100 series robust DPSS actively Q-switched sub-nanosecond lasers deliver multi-kW peak powers (> 700 kW) in less than 700 ps pulse duration at 1000 Hz repetition rate. Innovative short laser cavity is fixed on thermo-stabilized and controlled baseplate which gives extremely stable output parameters. Small footprint is welcome point for integration into OEM lasers.
Sub-nanosecond pulse duration of < 700 ps, pulse energy more than 0.5 mJ, repetition rate from 1 Hz to 1000 Hz covers broad spectrum of applications starting from LIBS, LIF, spectroscopy to supercontinuum generation. Standard optional harmonics generator to green (532 nm) and ultraviolet (355 nm, 266 nm) is also available.
| Features | Applications |
|
|
| Model | ||
| MPL15100 | MPL15100-1K | |
| Pulse energy | ||
| 1064 nm | 0.5 mJ | |
| 532 nm | 0.25 mJ | |
| 355 nm | 0.15 mJ | |
| 266 nm | 0.1 mJ | |
| Pulse to pulse energy stability (RMS) | ||
| 1064 nm | < 0.5 % 2) | |
| 532 nm | < 1.0 % 2) | |
| 355 nm | < 1.5 % 2) | |
| 266 nm | < 2.0 % 2) | |
| Typical pulse duration | < 700 ps 3) | |
| Power drift | ± 3.0 % 4) | |
| Pulse repetition rate 5) | 1 – 100 Hz | 1000 Hz |
| Beam spatial profile | Close to Gaussian | Close to Gaussian |
| Beam divergence 6) | < 5 mrad | |
| Polarization | Linear, horizontal at 1064 nm | |
| Spectral linewidth | SLM | |
| Beam pointing stability 7) | < 50 µrad | |
| Typical beam diameter 8) | 2 mm | 2 mm |
| Optical jitter | < 0.2 ns 9) | |
| Dimensions | ||
| Laser head (W×L×H) | 168 × 252 × 82 mm | |
| Controller unit (W×L×H) | 257 × 271 × 153 mm | |
| Cable cord length | 1 m | |
| Operating requirements | ||
| Cooling requirements | air-cooled | |
| Ambient temperature | 15 – 30 ºC | |
| Relative humidity | 10 – 80 % (non-condensing) | |
| Mains voltage | 100 – 240 VAC, single phase, 50 – 60 Hz | |
| Power consumption | < 10 W | < 30 W |
1. Due to continuous improvements all specifications are subject to change. Unless stated otherwise all specifications are measured at 1064 nm.
2. Averaged from 60 seconds time interval.
3. FWHM level at 1064 nm. Shorter pulse duration (< 350 ps) is available by request. Please inquire for detailed specifications.
4. Over 8-hours period after max 5 minutes of warm-up when ambient temperature variation is less than ±2 °C.
5. Factory-set pulse repetition rate is fixed at max repetition rate. Higher repetition rates are available, please inquire for details.
6. Full angle measured at the 1/e2 level.
7. RMS value measured from 60 seconds time interval.
8. Beam diameter is measured 20 cm from laser output at the 1/e2 level.
9. In respect to Q-switch triggering rising edge pulse.
Laser head dimensions:
Typical beam intensity profile (20 cm from laser output) of MPL15100 series lasers:
BROCHURE