MPL2310
DIODE PUMPED PICOSECOND PASSIVELY Q-SWITCHED LASER
MPL2310 series DPSS passively Q-switched picosecond lasers deliver high peak powers > 5 MW at 100 Hz repetition rate. Short laser cavity is fixed on thermo- stabilized and controlled baseplate which gives extremely stable output parameters performance. Small footprint is welcome point for integration into OEM lasers. Pulse duration of < 350 ps, high pulse energy more than 2 mJ, variable repetition rate from 1 Hz to 100 Hz covers many applications like pollution monitoring, DNA analysis, supercontinuum generation and many others.
Due to short pulse duration and high pulse energy laser delivers high peak power which is up to 5 MW. Optional conversion to green (532 nm) and ultraviolet (355 nm, 266 nm) is also available.
Stand alone with harmonics option
OEM version
| Features | Applications |
|
|
| Model | ||
| MPL2310 | ||
| Pulse energy: | ||
| at 1064 nm | 2 mJ | |
| at 532 nm | 1 mJ | |
| at 355 nm | 0.5 mJ | |
| at 266 nm | 0.25 mJ | |
| Typical pulse duration | < 350 ps 2) | |
| Pulse to pulse energy stability (RMS): | ||
| at 1064 nm: | < 1 % 3) | |
| at 532 nm: | < 2.0 % 3) | |
| at 355 nm: | < 3.0 % 3) | |
| at 266 nm: | < 4.0 % 3) | |
| Power drift | ± 3.0 % 4) | |
| Pulse repetition rate 5) | 1 – 100 Hz | |
| Beam profile | Close to Gaussian | |
| Beam divergence 6) | < 6 mrad | |
| Polarization | Linear, horizontal at 1064 nm | |
| Spectral Linewidth | SLM | |
| Beam pointing stability 7) | < 10 µrad | |
| Typical beam diameter 8) | 1.5 mm | |
| Jitter | ~ 2 µs RMS 9) | |
| Dimensions | ||
| Laser head (W×L×H) | 125 × 295 × 76 mm (with harmonics) | |
| 99 × 175 × 45.5 mm (OEM version) | ||
| Controller unit (W×L×H) | 257 × 271 × 153 mm | |
| 75 × 200 × 70 mm (OEM version) | ||
| Operating requirements | ||
| Cooling requirements | Air cooled | |
| Ambient temperature | 15 – 30 ºC | |
| Relative humidity | 10 – 80 % (non-condensing) | |
| Mains voltage | 100 – 230 VAC, single phase, 50 – 60 Hz 10) | |
| Power consumption | < 20 W | |
1. Due to continuous improvements all specifications are subject to change. Unless stated otherwise all specifications are measured at 1064 nm.
2. FWHM level at 1064 nm.
3. Averaged from 60 seconds time interval.
4. Over 8-hours period after max 5 minutes of warm-up when ambient temperature variation is less than ±2 °C.
5. Factory-set pulse repetition rate is fixed at 100 Hz repetition rate. Higher repetition rates are available, please inquire for more details.
6. Full angle measured at the 1/e2 level. Lower beam divergence is available upon request, please inquire for more details.
7. RMS value measured from 1000 shots.
8. Beam diameter is measured 20 cm from laser output at the 1/e2 level.
9. In respect to Q-switch triggering rising edge pulse.
10 Laser can be powered from an appropriate 12 VDC power source. Inquire for details.
Laser head dimensions:
MPL2310 series laser head dimensions (in mm)
MPL2310 series laser head dimensions OEM version (in mm)
Typical beam intensity profile (20 cm from laser output) of MPL2310 series lasers:
BROCHURE